Man, if everything fails, try AutoIt, I am sure it can make your
autosampler work at the right time. Contact me in private if you wish more
details. Regards,
Matheus C. Carvalho
Southern Cross University
Lismore, NSW, Australia
Editor of HardwareX (Elsevier):
http://www.journals.elsevier.com/hardwarex/editorial-board
Osmar, the open source microsyringe autosampler:
https://www.sciencedirect.com/science/journal/aip/24680672
Book: Practical Laboratory Automation Made Easy with AutoIt
http://www.wiley-vch.de/publish/en/books/ISBN978-3-527-34158-0/
YouTube channel: http://is.gd/lab_automation
On Sun, May 13, 2018 at 8:31 PM, Simon <[log in to unmask]> wrote:
> Hey Vladimir!
> I already tried it with an old isodat backup, but did not solve my
> problem! :-(
> Thanks a lot for your continuous input!!
>
> Best,
> Simon
>
>
> On 12.05.2018, at 16:37, Vladimir <[log in to unmask]> wrote:
>
> Hi, Simon. Did you create Backup Isodat in Version Handler when all system
> worked nice? If yes, do Restore. If not try to use Window restore point.
> Regards, Vladimir.
>
> Отправлено с помощью BlueMail <http://www.bluemail.me/r?b=12976>
> На 11 мая 2018 г., в 11:46, simon leitner <[log in to unmask]> написал:п
>>
>> Dear Vladimir!
>>
>> Today I made a new configuration without any AS. I started a new sequence
>> with a new IRMS method (isodat aquisition start: by device). I then
>> manually started the GC, but isodat stayed at "waiting for AS trigger".
>> hmm??
>>
>> best,
>> simon
>>
>> *Gesendet:* Mittwoch, 09. Mai 2018 um 12:36 Uhr
>> *Von:* Vladimir <[log in to unmask]>
>> *An:* [log in to unmask]
>> *Betreff:* Re: [ISOGEOCHEM] "GC injected" signal not received by isodat
>> Hello Simon,
>> But now do the configuration without of any AS, but with GC and see the
>> start Acquisition after click in the Start button on GC. If all will be OK,
>> do the new Isodat configuration with AS and new method and Sequence.
>> Regards, Vladimir.
>>
>> Отправлено с помощью BlueMail <http://www.bluemail.me/r?b=12874>
>> На 8 мая 2018 г., в 14:23, Simon < [log in to unmask]> написал:п
>>>
>>> Dear Vladimir!
>>>
>>> It is the same for both autosamplers!
>>>
>>> Simon
>>>
>>> On 07.05.2018, at 23:42, Vladimir < [log in to unmask]> wrote:
>>>
>>>
>>> Hello Simon,
>>> You wrote:
>>> ... but after the autosampler injected a sample and the GC switches from
>>> "ready to inject" to "initial temp" isodat is not starting to measure
>>> Which Autosampler You mean here? GC PAL?
>>> Vladimir.
>>>
>>> Отправлено с помощью BlueMail <http://www.bluemail.me/r?b=12874>
>>> На 7 мая 2018 г., в 15:12, Simon Leitner < [log in to unmask]> написал:п
>>>>
>>>> Dear Heavy Users!
>>>>
>>>> We have a Thermo Trace GC Ultra connected to a Delta V Advantage via GC Isolink and Conflo IV. The GC is equipped with two different autosamplers (VSP purge&trap, combi pal). A data transfer switch is used to change the communication from/to the GC with either one of the two samplers. The data aquisition is controlled/started via isodat 3.0. The system has been running since some weeks ago when I was changing from on-column injection by the VSP to PTV splittless injection by the combi pal (then i was also working on some errors with the PTV...)
>>>> We now have the problem that isodat is not starting a "by device" run within a sequence. Isodat is as usually "waiting for AS trigger", but after the autosampler injected a sample and the GC switches from "ready to inject" to "initial temp" isodat is not starting to measure, executing the IRMS method respectively. While the previous steps of starting a run, waiting for "GC ready" and starting the injection by the autosampler is executed.
>>>> Since I was klicking through the isodat configurator unaware that I maybe changed something I loaded an isodat backup, but our problem stayed the same.
>>>> I should maybe add how the individual devices are connected to each other. The Isodat PC is connected via fiberline to the IRMS and the GC Isolink and by a COM cable to the GC. The GC is connected to the autosamplers via the "autosampler signals" plug-in and to the GC isolink and a second detector (Thermo ISQ) via the "generic handshake" plug-in (Y-cable). The connections are as they used to be when the measurement setup was running properly.
>>>> Does anyone has a clue why the GC start signal is not received by isodat or how I could check if the GC signal is sent to isodat. Or is there any advise what to do in general?
>>>> Thanks a lot!
>>>>
>>>> simon
>>>>
>>>>
|
